
Practical point: On a capacitive-sensor analyzer, the most useful result is not one absolute number. It is the difference between cylinders measured the same way, on the same engine, at the same RPM.
Table of Contents
- Why “Spark / No Spark” Is Not Enough
- What an Ignition Analyzer Measures
- Which Ignition Systems Can Be Tested
- How to Read Peak Voltage and Burn Time
- A Practical Spark Plug Testing Workflow
- Where Workshops Use an Ignition Analyzer
- Ignition Analyzer vs Spark Tester vs Oscilloscope
- What an Ignition Analyzer Cannot Tell You
- What B2B Buyers Should Confirm Before Ordering
- Where the QBH WT05 Fits
- FAQ
Why “Spark / No Spark” Is Not Enough
A basic spark tester answers one question: is there a spark? That is useful for a no-start, but it is much less useful for the problems technicians see most often. A cylinder can produce a visible spark in open air and still misfire under compression, because the voltage needed to fire a plug inside the cylinder is far higher than the voltage needed to jump a gap outside it.
Intermittent misfires, rough idle, hesitation under load and poor fuel economy often come from a spark that exists but is weak, short or inconsistent. Finding the cylinder responsible by trial and error means swapping coils, replacing plugs and repeating the test drive.
An ignition analyzer takes a different approach. It reads the spark event of each cylinder while the engine is running and puts numbers on it. That turns a guess into a comparison.
What an Ignition Analyzer Measures
A multi-system ignition analyzer such as the QBH WT05 reports three core values, plus the ignition system and cycle type being tested.
| Reading | What It Represents | Why It Matters |
|---|---|---|
| Engine speed (RPM) | Engine speed derived from the ignition signal | Lets you compare readings at the same idle or test speed, and works without a separate tachometer connection. |
| Peak high voltage | The voltage spike needed to break down the plug gap and start the spark | Shows how hard the ignition system is working to fire each plug. |
| Spark burn time | How long the spark continues to burn after it has started | A short burn time can point to a fouled plug or high resistance in the secondary circuit. |
| Min / max values | The lowest and highest readings captured during the test | Helps catch intermittent drops that disappear before you can read the screen. |
Peak voltage and burn time together are more informative than either one alone. A plug with a worn, widened gap and a plug with carbon tracking can both cause a misfire, but they usually show different combinations of the two readings.
Which Ignition Systems Can Be Tested
Modern workshops rarely see only one ignition layout. A useful analyzer needs to work across the systems that actually come through the door, including small engines that are often ignored by car-focused tools.
| Ignition System | Typical Application | Testing Consideration |
|---|---|---|
| COP (Coil-on-Plug) | Most modern gasoline passenger cars | Place the sensor against each coil in turn and keep the position the same for every cylinder. |
| Coil near plug | Engines with a remote coil and a short plug lead | Test at the coil or lead for each cylinder, using one consistent position. |
| SPW (Spark Plug Wire) | Older vehicles and many industrial or marine engines | Test on each plug wire. This also helps reveal wire and boot problems. |
| DIS (Distributorless) | Waste-spark systems that fire two cylinders at once | Remember that a coil serves a pair of cylinders. A fault may sit on the companion cylinder. |
| Conventional / magneto | Small engines, generators, motorcycles, outdoor power equipment | Confirm the tester supports 2-cycle and 4-cycle gasoline engines. |
The ignition type, cycle and engine speed shown on the display help confirm that the tool is reading the engine the way you expect before you start comparing cylinders.
How to Read Peak Voltage and Burn Time
On a lab oscilloscope, a healthy secondary ignition event is often described with a firing voltage in roughly the 8 to 15 kV range at idle and a spark burn time of about 1.0 to 2.0 ms. Comparing burn time between cylinders is a long-established engine-analyzer technique (see, for example, US5245324 on Google Patents). These figures are a useful reference, but they vary with ignition design, plug gap, compression, mixture and engine load. Treat them as a general guide, not a pass/fail limit for every engine.
The more reliable method is comparison:
Compare Cylinder to Cylinder
On a healthy engine, similar cylinders should give similar readings. The cylinder that stands out from the others is the one to investigate first.
Read Voltage and Burn Time Together
A single reading can mislead. High peak voltage with short burn time points in a different direction than low peak voltage with short burn time.
Keep Conditions Constant
Test at the same RPM, with the sensor in the same position and distance on every cylinder. Changing the position changes the reading.
Use Min / Max to Catch Intermittents
A fault that appears for a moment can be missed by eye. Stored minimum and maximum values help show whether a cylinder is dropping out.
| What You See | Possible Causes | Recommended Next Step |
|---|---|---|
| One cylinder with higher peak voltage and shorter burn time | Worn or widened plug gap, high resistance in a plug wire or boot, lean mixture on that cylinder | Inspect the plug gap and wire. See our spark plug gap chart for reference sizes. |
| One cylinder with lower peak voltage and short burn time | Fouled or carbon-tracked plug, oil or fuel contamination, leaking boot or insulation | Remove the plug and check its condition. The spark plug color chart can help you read the deposits. |
| All cylinders lower than expected | Weak battery or charging system, supply voltage problem, system-wide ignition issue | Check battery and charging voltage before blaming individual coils. |
| One cylinder reading unstable or dropping out | Failing coil, intermittent connector, cracked insulation | Swap the coil to another cylinder and see whether the fault follows it. |
| No reading on one cylinder | No spark, sensor not positioned correctly, open circuit in that ignition path | Re-check sensor placement first, then test coil supply and control. |
Remember that these are screening results. They tell you where to look, not what the final repair is.
A Practical Spark Plug Testing Workflow
A repeatable process matters more than the instrument. The following sequence keeps the readings comparable.
Warm Up Engine
Set Sensor
Read Each Cylinder
Compare and Confirm
Step 1: Identify the Ignition System
Confirm whether the engine uses COP, coil-near-plug, plug wires, DIS or a magneto, and whether it is a 2-cycle or 4-cycle engine. Select the matching mode on the analyzer.
Step 2: Bring the Engine to a Stable Condition
Run the engine to normal operating temperature and hold a steady idle. Readings taken during a cold, unstable idle are harder to compare.
Step 3: Position the Sensor Consistently
Bend the flexible gooseneck so the capacitive sensor touches or sits near the coil or plug wire at the same angle each time. Keep it away from other cylinders’ coils and wires to avoid cross-pickup.
Step 4: Read Every Cylinder
Record RPM, peak voltage and burn time for each cylinder in firing order. Do not stop at the first cylinder that looks wrong. The reference is the group, not a single reading.
Step 5: Repeat Under Different Conditions
If the complaint appears under load or at higher speed, repeat the measurements with a light rev and check the min/max values. Some faults only appear when demand on the ignition increases.
Step 6: Confirm With the Right Next Test
Use the result to decide what to inspect: plug condition, plug gap, wire resistance, coil swap or fuel and compression checks. If the spark readings look normal but the engine still misfires, move on. Our engine misfire guide covers the non-ignition causes.
Safety note: Ignition systems produce dangerous high voltage and the engine is running during the test. Keep hands, clothing and the tester’s flexible probe clear of belts, fans and hot exhaust parts, and never hold a plug wire while the engine is running.
Where Workshops Use an Ignition Analyzer
Misfire Diagnosis
Narrow a misfire to the responsible cylinder before removing any parts. This is faster than swapping coils on every cylinder, and it pairs well with an OBD code such as P0301.
Spark Plug Service Checks
Check the result of a plug replacement, or screen a vehicle to decide whether plugs are due. It complements the guidance in our spark plug replacement guide.
Plug Wire and Coil Screening
On wire-based systems, readings can reveal high-resistance wires and boots. On COP engines, they help separate a weak coil from a weak plug.
Small Engines and Motorcycles
Support for 2-cycle and 4-cycle engines makes the same tool useful for motorcycles, generators, lawn equipment and marine outboards, where a scope is rarely practical.
Ignition Analyzer vs Spark Tester vs Oscilloscope
| Tool | Best For | Limitation |
|---|---|---|
| Spark tester | Quick check that a spark exists at the plug | Does not measure burn time or voltage, and an open-air spark does not prove the spark is strong under compression. See our spark tester buyer’s guide. |
| Ignition analyzer | Fast, numeric cylinder-to-cylinder comparison during normal workshop work | Gives screening values, not a full waveform. |
| Oscilloscope | Detailed waveform analysis and root-cause confirmation | Needs more setup, more training and more time per vehicle. |
| Ignition coil tester | Checking a coil’s output or resistance on its own | Tests the coil, not the whole spark event in the running engine. See the ignition coil tester guide. |
For many workshops the sensible approach is layered: use an analyzer to find the suspect cylinder quickly, and reserve the oscilloscope for the cases that remain unclear.
What an Ignition Analyzer Cannot Tell You
An ignition analyzer measures the spark event. It does not measure everything that can cause a misfire.
A capacitive-sensor analyzer does not clamp into the secondary circuit, so its voltage reading is best used as a relative indicator between cylinders rather than a calibrated kV measurement. It cannot show a full waveform, and it cannot diagnose fuel delivery, compression, valve timing or vacuum leaks. It cannot confirm the final fault by itself either, so a suspect result should always be verified by inspecting the plug, wire or coil.
Use the right test for the question. If the question is “which cylinder has a weak spark?”, an ignition analyzer is a fast answer. If the question is “why is this cylinder weak?”, follow up with inspection, component testing or a scope.
What B2B Buyers Should Confirm Before Ordering
For distributors, tool brands and workshop-equipment suppliers, the specification sheet should be matched to the markets you sell into.
| Requirement | What to Confirm |
|---|---|
| Ignition system coverage | COP, coil near plug, SPW, DIS and conventional or magneto systems |
| Engine cycle support | 2-cycle and 4-cycle gasoline engines, if you sell to motorcycle or small-engine customers |
| Displayed readings | RPM, peak high voltage, burn time and min/max hold |
| Sensor type and reach | Capacitive sensor sensitivity and flexible probe length for tight engine bays |
| Power supply | Battery type, battery life and auto power-off behavior |
| Durability | Rubber protective sleeve, anti-slip and wear-resistant housing for daily workshop use |
| Display and language | LCD readability and language requirements for your market |
| OEM requirements | For private-label projects, confirm logo, housing color, packaging, manual and accessories |
Before requesting a quotation, tell the supplier which vehicle or engine types your customers mostly service. That makes it easier to decide whether a standard model or a customized configuration is the better match.
Where the QBH WT05 Fits
ShenZhen QBH Technology Development Co., Ltd. develops automotive inspection and diagnostic tools for professional B2B customers. The WT05 is a multi-system ignition analyzer designed for quick ignition coil and spark plug screening on gasoline engines.
It supports COP and SPW ignition testing and works with plug coil, plug-near coil, DIS and conventional magneto systems on 2-cycle and 4-cycle gasoline engines. The LCD displays engine RPM (200 to 19,999 RPM), spark peak voltage (0 to 50 kV) and spark burn time (0 to 10 ms) with max/min capture, plus indicators for high-voltage warning, ignition system and battery level. A high-sensitivity capacitive sensor on a 35 cm flexible gooseneck can be shaped at will to reach tight positions. The unit runs on a 9V battery, offers approximately 20 hours of use on an alkaline cell, shuts off automatically after 3 minutes of inactivity and has a rubber protective sleeve for workshop handling.
The WT05 sits alongside other QBH automotive testers, including the WT07 battery tester, so distributors can build a more complete workshop-tool range from one supplier.
Explore the QBH WT05 Ignition Analyzer →
Looking for an Ignition Analyzer for Your Market?
Send QBH your target customers, engine types, quantity and any OEM/ODM requirements. Our team can review the application and recommend a suitable configuration for standard purchasing or private-label projects.
FAQ
An ignition analyzer measures the spark event on a running gasoline engine, typically showing RPM, peak voltage and spark burn time. Technicians use it to find weak cylinders, faulty spark plugs, high-resistance wires and failing coils.
Spark burn time is how long the spark continues to burn across the plug gap after it has started. On a scope it is often around 1 to 2 ms, but the right value depends on the engine. A cylinder with a much shorter burn time than the others deserves a closer look.
Yes, as a first screening step. An ignition analyzer reads the spark from outside the coil or plug wire while the engine runs, so you can identify the suspect cylinder before pulling plugs. Inspecting the plug is still the way to confirm its condition.
They answer different questions. A spark tester checks whether a spark exists. An analyzer measures how strong and how long the spark is, which is more useful for intermittent misfires and weak-spark problems.
A multi-system analyzer such as the WT05 supports both COP and SPW ignition, as well as coil-near-plug, DIS and conventional magneto systems. Always confirm coverage for the ignition types your customers use.
The WT05 is compatible with 2-cycle and 4-cycle gasoline engine testing, so it can be used on motorcycles and many small gasoline engines as well as cars. Actual results depend on the ignition type and sensor position.
No. An analyzer is a fast screening tool that gives numeric readings. An oscilloscope shows the full waveform and is better for confirming root causes. Many workshops use the analyzer first and the scope only when needed.
Provide your target market, the engine types your customers service, expected order quantity, language and packaging needs, and any OEM or private-label requirements such as logo and housing color.
Product Line
Article tag
Leave A Comment
Related Posts
The right borescope accessories can change what an inspection camera is able to see, reach, retrieve and survive—but every attachment also changes the size, balance [...]
You cannot keep every borescope inspection camera completely away from a pipe wall, but you can reduce damaging scraping by matching the camera head and [...]
A borescope can reveal visible turbine engine failure signs such as impact damage, deposits, erosion, coating loss, heat-affected areas, blocked cooling holes and missing material [...]
The right borescope accessories can change what an inspection camera is able to see, reach, retrieve and survive—but every attachment also changes the size, balance [...]
You cannot keep every borescope inspection camera completely away from a pipe wall, but you can reduce damaging scraping by matching the camera head and [...]
A borescope can reveal visible turbine engine failure signs such as impact damage, deposits, erosion, coating loss, heat-affected areas, blocked cooling holes and missing material [...]
A push camera is usually the practical choice for small drain lines, laterals and portable service work, while a sewer crawler camera is better suited [...]









